#! /bin/sh
# Copyright (c) 1995-2004 SuSE Linux AG, Nuernberg, Germany.
# All rights reserved.
#
# Author: Stanislav Brabec <sbrabec@suse.cz>
#
# /etc/init.d/smartd
#
### BEGIN INIT INFO
# Provides:          smartd
# Required-Start:    $syslog
# X-UnitedLinux-Should-Start: $sendmail
# Required-Stop:     $syslog
# X-UnitedLinux-Should-Stop:
# Default-Start:     2 3 5
# Default-Stop:
# Short-Description: Monitors disk and tape health via S.M.A.R.T.
# Description:       Start S.M.A.R.T. disk and tape monitor.
### END INIT INFO
# 
# 


# Check for missing binaries (stale symlinks should not happen)
SMARTD_BIN=/usr/sbin/smartd
test -x $SMARTD_BIN || exit 5

# Existence of config file is optional
SMARTD_CONFIG=/etc/smartd.conf

# Shell functions sourced from /etc/rc.status:
#      rc_check         check and set local and overall rc status
#      rc_status        check and set local and overall rc status
#      rc_status -v     ditto but be verbose in local rc status
#      rc_status -v -r  ditto and clear the local rc status
#      rc_status -s     display "skipped" and exit with status 3
#      rc_status -u     display "unused" and exit with status 3
#      rc_failed        set local and overall rc status to failed
#      rc_failed <num>  set local and overall rc status to <num>
#      rc_reset         clear local rc status (overall remains)
#      rc_exit          exit appropriate to overall rc status
#      rc_active	checks whether a service is activated by symlinks
#      rc_splash arg    sets the boot splash screen to arg (if active)
. /etc/rc.status

# Reset status of this service
rc_reset

# Return values acc. to LSB for all commands but status:
# 0	  - success
# 1       - generic or unspecified error
# 2       - invalid or excess argument(s)
# 3       - unimplemented feature (e.g. "reload")
# 4       - user had insufficient privileges
# 5       - program is not installed
# 6       - program is not configured
# 7       - program is not running
# 8--199  - reserved (8--99 LSB, 100--149 distrib, 150--199 appl)
# 
# Note that starting an already running service, stopping
# or restarting a not-running service as well as the restart
# with force-reload (in case signaling is not supported) are
# considered a success.

case "$1" in
    start)
	echo -n "Starting smartd "
	## Start daemon with startproc(8). If this fails
	## the return value is set appropriately by startproc.
	startproc $SMARTD_BIN -p /var/run/smartd.pid

	# Remember status and be verbose
	rc_status -v
	;;
    stop)
	echo -n "Shutting down smartd "
	## Stop daemon with killproc(8) and if this fails
	## killproc sets the return value according to LSB.

	killproc -TERM $SMARTD_BIN

	# Remember status and be verbose
	rc_status -v
	;;
    try-restart|condrestart)
	## Do a restart only if the service was active before.
	## Note: try-restart is now part of LSB (as of 1.9).
	## RH has a similar command named condrestart.
	if test "$1" = "condrestart"; then
		echo "${attn} Use try-restart ${done}(LSB)${attn} rather than condrestart ${warn}(RH)${norm}"
	fi
	$0 status
	if test $? = 0; then
		$0 restart 
	else 
		rc_reset	# Not running is not a failure.
	fi
	# Remember status and be quiet
	rc_status
	;;
    restart | force-reload )
	## Stop the service and regardless of whether it was
	## running or not, start it again.
	$0 stop
	$0 start

	# Remember status and be quiet
	rc_status
	;;
    reload)
	## Like force-reload, but if daemon does not support
	## signaling, do nothing (!)
	echo -n "Reload service smartd "
	killproc -HUP ${SMARTD_BIN}
	rc_status -v
	;;
    status)
	echo -n "Checking for service smartd "
	## Check status with checkproc(8), if process is running
	## checkproc will return with exit status 0.

	# Return value is slightly different for the status command:
	# 0 - service up and running
	# 1 - service dead, but /var/run/  pid  file exists
	# 2 - service dead, but /var/lock/ lock file exists
	# 3 - service not running (unused)
	# 4 - service status unknown :-(
	# 5--199 reserved (5--99 LSB, 100--149 distro, 150--199 appl.)
	
	# NOTE: checkproc returns LSB compliant status values.
	checkproc $SMARTD_BIN
	# NOTE: rc_status knows that we called this init script with
	# "status" option and adapts its messages accordingly.
	rc_status -v
	;;
    probe)
	## Optional: Probe for the necessity of a reload, print out the
	## argument to this init script which is required for a reload.
	## Note: probe is not (yet) part of LSB (as of 1.2)

	test $SMARTD_CONFIG -nt /var/run/smartd.pid && echo reload
	;;
    *)
	echo "Usage: $0 {start|stop|status|try-restart|restart|force-reload|reload|probe}"
	exit 1
	;;
esac
rc_exit
